Car care
When should you replace your tyres? Tread depth and age
The legal tread limit in Australia, why grip fades before you reach it, how to read a tyre's age, and when old tyres with good tread should still go.
Published 15 November 2026 · 5 minute read · By Safal Aryal, MechAxis co-founder
Two limits: tread and age
Tyres wear out in two ways. The tread wears down with distance, and the rubber hardens and cracks with age. Most people watch only the first. A car that covers few kilometres can have tyres with plenty of tread that are too old to grip properly, which is the point of posts like 'PSA: Check the age of your tyres!' on r/sydney. The opposite doubt appears in the r/CarsAustralia thread 'Replacing tyres too early?', where an owner questions a recommendation to replace tyres that still look serviceable. Both questions have a factual answer you can check yourself in a few minutes.
The legal minimum is 1.5 mm
The NRMA states that the minimum legal tread depth in Australia is 1.5 mm, and that a new tyre typically starts with about 8 mm. Tyres have tread wear indicators, small raised bars across the main grooves. When the tread is level with those bars anywhere on the tyre, it is worn out and unroadworthy. Check across the full width, not just the outer edge you can see, because the inside shoulder often wears first. A cheap tread depth gauge is more reliable than a coin, and any tyre shop or workshop will measure for you.
Why many tyres should go before the legal limit
Tread exists to clear water from under the tyre. As the grooves get shallower they move less water, so wet braking distances grow and the risk of aquaplaning rises well before 1.5 mm. For that reason a number of tyre and motoring sources suggest planning replacement at around 3 mm rather than running to the legal minimum. You do not need to treat 3 mm as a hard rule. Treat it as the point to start getting quotes, particularly before winter or a long trip, instead of discovering the tyres are illegal at a roadworthy inspection.
How to read a tyre's age
Every tyre carries a manufacture date on the sidewall. Look for the letters DOT followed by a code that ends in four digits. The first two are the week and the last two are the year, so 0816 means the eighth week of 2016. Michelin recommends having tyres checked by a professional at least once a year once they are five years old, and replacing any tyre that reaches ten years from its date of manufacture as a precaution, even if it looks usable. That advice includes the spare, which is often the oldest tyre on the car.
Signs a tyre is finished regardless of tread
Look at the sidewalls when you check pressures. The NRMA lists cuts, bulges and missing chunks, usually from kerbs and potholes, as reasons a tyre can be unsafe and unroadworthy. A bulge means the internal structure has separated and the tyre can fail without warning. Fine cracks in the sidewall, called crazing, come from sunlight and ozone and are common on cars parked outside or near the coast. Vibration at speed, repeated pressure loss and a repair in the sidewall area are also reasons to have the tyre assessed.
Uneven wear is a message about the car
A tyre worn on one edge, or in patches, is usually telling you about alignment, suspension or pressure rather than the tyre itself. Fitting new tyres without fixing the cause wears out the new set the same way. The NRMA suggests a wheel alignment every 12 months or 20,000 km to protect tyre life. Rotating tyres at service time evens out wear between the front and rear. Check pressures monthly when the tyres are cold, using the placard figures inside the driver's door or fuel flap, not the maximum printed on the tyre.
Is the recommendation to replace fair?
If a workshop says your tyres need replacing, ask for three numbers: the tread depth on each tyre in millimetres, the date code, and where the wear is. A recommendation backed by measurements and a photo is easy to trust or to check elsewhere. Workshops that use MechAxis record inspection findings with measurements and photos and mark them green, amber or red, so you can see whether a tyre is illegal now or simply worth budgeting for. Replace tyres in axle pairs at least, and ask about matching on all-wheel-drive cars.
Sources
- NRMA: the two signs your car needs new tyres
- Michelin Australia: how long do tyres last?
- RACV: tyre maintenance, roadworthy checks and when to replace them
- Drive: how long do tyres actually last, and do they have a use-by date?
- Reddit r/CarsAustralia: Replacing tyres too early?
- Reddit r/sydney: PSA: Check the age of your tyres!
Common questions
01What is the legal tread depth in Australia?+
1.5 mm. If the tread is level with the wear indicator bars anywhere on the tyre, it is unroadworthy.
02How old is too old for a tyre?+
Michelin advises yearly professional checks from five years of age and replacement at ten years from the date of manufacture, whatever the tread looks like. Cracked or bulging tyres should be replaced sooner.
03Do I need to replace all four tyres at once?+
Not always. Replace at least in axle pairs so grip is even left to right. Some all-wheel-drive systems are sensitive to different tyre diameters, so check the handbook or ask your workshop.
04Is a ten-year-old spare tyre safe?+
Treat it as due for replacement. A spare ages even if it has never touched the road, and it is used in exactly the situation where you need it to work.
Run a workshop?
MechAxis keeps bookings, inspections, quotes and each vehicle's service history in one place, so your customers get clear answers like these. Try it free for 30 days.
Start free trial