Car care

Which engine oil does your car need? 0W-20 vs 5W-30

How to read an oil grade, why the specification matters more than the brand, and whether thicker oil really protects an older engine.

Published 15 November 2026 · 5 minute read · By Safal Aryal, MechAxis co-founder

01

Start with the handbook, not the shelf

The right oil for your car is the one that matches two things in the owner's manual: a viscosity grade, such as 0W-20 or 5W-30, and a performance specification, such as API SP, an ACEA category like C3, or a car maker's own approval code. Brand is the least important part of the choice. A budget oil that meets the listed specification is a better match than a premium oil that does not. If the manual lists more than one grade for different temperatures, any listed grade is acceptable. If you no longer have the manual, the oil filler cap, the manufacturer's website or your workshop can confirm it.

02

What the numbers mean

A grade such as 5W-30 describes how the oil flows at two temperatures. The first number with the W (for winter) rates cold flow: the lower it is, the more easily the oil moves at start-up. The second number rates thickness at normal operating temperature, around 100 degrees Celsius. So 0W-20 and 5W-20 are similar once hot, but the 0W reaches the top of a cold engine sooner. Most engine wear happens in the first moments after a cold start, before oil has reached every surface, which is why modern engines favour low first numbers even in a warm country.

03

Is thicker oil better for Australian heat?

This is the argument behind long Reddit threads such as '0w20 or 5w30 in Australia?' on r/CarsAustralia and 'Should I run 5w-30 in an 0w-20 engine' on r/MechanicAdvice, which drew hundreds of comments. The engine's cooling system holds oil temperature in a narrow band whether it is 15 or 40 degrees outside, so the weather changes less than people expect. Engines designed for thin oil have tight clearances, small oil passages and hydraulic parts such as variable valve timing that are calibrated for that viscosity. Thicker oil can flow more slowly at start-up and cost a little fuel economy. Only go thicker if your manual lists the heavier grade as an option.

04

The specification is doing the real work

Viscosity is only half the label. The specification covers detergents, wear protection, deposit control and compatibility with emissions equipment. Getting it wrong can be expensive. Diesels with a particulate filter need low-ash oil (the ACEA C categories), because the wrong oil leaves ash that the filter cannot burn off. Small turbocharged petrol engines need oils tested against low-speed pre-ignition. Engines with a timing belt that runs in oil need exactly the specified oil, because the wrong chemistry can attack the belt. Many European cars require a specific maker approval rather than a generic category.

05

What about high-kilometre engines?

Another popular thread asks why older mechanics keep recommending thicker oil for high-kilometre engines. There is some logic to it. A worn engine with wider clearances that burns or leaks oil can sometimes be quieter and use less oil on the next grade up, and high-mileage oils add seal conditioners. That is a treatment for a worn engine, decided with a mechanic who has looked at it. It is not preventive care for a healthy engine at 150,000 km. A well-maintained engine can stay on its specified grade for life.

06

Synthetic, top-ups and change intervals

Most current cars specify a full synthetic or synthetic-blend oil, and the long service intervals in modern logbooks assume it. Putting mineral oil in such an engine and keeping the long interval is a false saving. Check the dipstick or the dash oil-level display monthly, since some engines use oil between services by design. Top up with the same grade and specification where you can. In an emergency any oil is better than running low, but change it at the next opportunity. Keep to the logbook interval, and shorten it if you tow, drive in dust or mostly do short trips.

07

How to check what your workshop used

Your invoice should state the oil grade and specification, not just 'engine oil'. If it does not, ask. This matters for warranty, because the ACCC notes that a warranty typically lets you choose your repairer as long as the manufacturer's servicing standards are met, and the oil specification is part of those standards. Workshops that use MechAxis record the parts and fluids used on each job against the vehicle, so the same oil can be matched at the next service and the history shows it was right.

Sources

Common questions

01Can I use 5W-30 instead of 0W-20?+

Only if your owner's manual lists 5W-30 as an approved alternative. Some do, particularly for hot climates or hard use. If it does not, stay with the specified grade.

02Does the oil brand matter?+

Much less than the grade and specification. Choose any reputable oil that states on the label that it meets the specification in your manual.

03How often should I check my oil level?+

About once a month and before a long trip. Low oil level does more damage than slightly old oil, and some engines use a noticeable amount between services.

04Is it bad to mix different oils?+

Mixing two oils of the correct grade and specification for a top-up is fine. Mixing in an oil of the wrong specification is acceptable to get home, but have the oil changed soon after.

Run a workshop?

MechAxis keeps bookings, inspections, quotes and each vehicle's service history in one place, so your customers get clear answers like these. Try it free for 30 days.

Start free trial